Rod seals provider from dmsseals.com
Hydraulic seals factory today: A basic mechanical seal contains three sealing points. The stationary part of the seal is fitted to the pump housing with a static seal –this may be sealed with an o-ring or gasket clamped between the stationary part and the pump housing. Rotating and Stationary parts of a Seal – The rotary portion of the seal is sealed onto the shaft usually with an O ring. This sealing point can also be regarded as static as this part of the seal rotates with the shaft. The mechanical seal itself is the interface between the static and rotary portions of the seal. One part of the seal, either to static or rotary portion, is always resiliently mounted and spring loaded to accommodate any small shaft deflections, shaft movement due to bearing tolerances and out-of-perpendicular alignment due to manufacturing tolerances. See more information on wiper seals.
What are Mechanical Seals? Mechanical seals are devices that accommodate a rotating shaft while containing and preventing the fluid from leaking out of the enclosed housing. While different mechanical seal designs are available for pumping applications, most have three sealing points. Rotating face that rotates with the shaft; Stationary face fitted to the pump housing; Interface portion between the rotating and stationary face of the seal. These three sealing points ensure that the fluid contained within the pump housing does not leak while also preventing dust particles in the atmosphere from entering the housing. The mechanical seals are usually made up of different materials to prevent sticking. Typically, one side of the seal uses softer materials like carbon graphite, and the other is made of harder materials such as silicon carbide or ceramic alumina. However, hard materials are preferred for both surfaces if the pumping application involves abrasive fluids. In addition to the two materials, the sealing unit also comes with O-rings to seal the stationary face on the housing side and the rotating face on the shaft side. Springs are also used to keep both faces pressed. In most cases, the two faces of the seals are also lubricated to prevent friction and wear. Depending on the application, this fluid film can either be a separate lubricant or the process fluid itself.
Good sealing performance: Because the system works outdoors, there is no leakage oil recovery system, and the working medium will directly pollute the environment after leakage, so external leakage requirements are strict. At the same time, for the requirements of hydraulic oil heating control, pressure maintaining or maintaining position, the internal leakage requirements are also very strict. High pressure: The working pressure of the hydraulic system is high, usually above 20MPa, and the highest is about 40Mpa, which is higher than the general industrial hydraulic system pressure, so the sealing pressure resistance requirements are high.
It is ideal for single-acting sealing of reciprocating piston rods or pistons with a wide operating pressure range of up to 20 MPa. The operating temperature range is also wide from -200°C to + 250°C. It has a diameters range from 3 mm to 1600 mm and a working speed of 5 m/s. The seal has a low coefficient of friction and the friction between the contact faces is minimal among all seal types. Moreover, the contact pressure between the mating surfaces is low. It can work without lubrication and is very wear resistant. And it has a long service life.
Rubber seals are a common type of basic component in sealing devices, and play a very important role in the contradiction between leakage and sealing. Using rubber seals is an important way to promote technological advancement and prevent and reduce environmental pollution. They are a class of rubber products that are widely used in sealing technology. Because rubber is a polymer material with valuable elasticity, a wide temperature range. It gives less stress in different media producing large deformation, which can provide contact pressure, compensate for leakage gap, and achieve the purpose of sealing.
Scraper seals are also known as wiper seals. The scraper sealof DMS SEALS can effectively prevent various forms of contamination that cause a hydraulic system failure. It can be mounted on the outside of the piston rod seal of the hydraulic cylinder to protect the hydraulic cylinder from dirt, dust and moisture. It can well protect the hydraulic cylinder from environmental pollution and effectively prevent damage to the hydraulic cylinder parts, causing the system to malfunction. DMS offers a wide range of wiper seals for different hydraulic systems with different characteristics, specifications and combinations.
Leakage of gaskets: There are four types of leakage phenomenon in general gaskets: interface leakage, penetration leakage, diffusion leakage, and damage leakage. Interface leaks: The interface will leak at the sealing interface due to insufficient gasket compression, improper flange joint surface finish, and flange deformation. For interface leakage, it can be prevented by using soft gasket to clamp in the flange face. Penetration leakage: Since most of the soft materials are made of fibers, they are easily soaked by the medium, especially the pressure. Due to capillary phenomenon, the medium will permeate to the low pressure side, forming permeation.
We own a number of invention patents and leading production process. The R&D teams have the ability to design and develop seals for various of complicated working condition of sealing system. We have already passed the certification of ISO 9001 and IATF 16949. We have the mature technical reserve for the solution of ultra-high temperature, ultra-high pressure, ultra-low temperature, highly corrosive and other special working condition. Find extra info at https://www.dmsseals.com/.
DMS Seals is a scientific and technical mechanical seal manufacturer and oil seal supplier specializing in seal production, sealing material development, and the conception of sealing solutions for special working conditions. We have 120 employees, including 70 senior technicians. DMS Seals has a number of invention patents and leading production processes. The R&D team is able to design and develop Rubber Seal & Hydraulic Seals for various mechanical sealing systems under complex conditions. We have already passed the certification of ISO 9001 and TS 16949.